Skip to content
CabinetHub

Casework vs Millwork Explained for Cabinet Shops

Updated · 9 min read

In this guide
  1. Casework vs millwork: the short answer
  2. What is casework?
  3. What is millwork?
  4. Comparison table
  5. Where each appears in the specs (MasterFormat)
  6. Who builds and installs each
  7. How casework and millwork are bid differently
  8. Examples by building type
  9. The gray areas
  10. Getting the scope right
  11. Frequently asked questions

Casework vs millwork comes down to boxes versus everything else. Casework is cabinetry: base cabinets, wall cabinets, tall storage, shelving units and other box-built storage. Millwork is the broader family of architectural woodwork made in a shop, such as trim, paneling, door frames, reception desks and custom built-ins. In the narrow sense, casework is one category inside millwork.

The distinction matters for more than vocabulary. On a commercial job the two often sit in different spec sections, carry different quality requirements, get bid by different subcontractors and get installed on different schedules. If you misread which is which, you either bid scope that isn't yours or miss scope that is.

Casework vs millwork: the short answer

Casework is factory- or shop-built cabinetry made of boxes with doors, drawers and shelves. Millwork is any architectural woodwork produced in a mill or shop, including trim, paneling, stair parts, doors, frames and custom fixtures. Casework is usually treated as a subset of millwork, but on commercial drawings and specs the two are often scoped and bid separately.

What is casework?

Casework is anything built as a case: a box with a top, bottom, sides and back, closed with doors or drawers or left open with shelves. In commercial construction the word covers classroom storage, nurse station cabinets, lab cabinets, break room cabinets and office storage walls. In residential work most people just say "cabinets."

Casework is defined by repetition and standard construction. A school might have 300 cabinets that are mostly the same dozen types in different widths. Most of it is built frameless in commercial work and either frameless or face frame in residential. Shops that build it lean on standard box construction, CNC cutting and edgebanding, and the price is driven by box count and hardware more than by craftsmanship on any one piece.

For a deeper look at the commercial side, including laminate construction and AWS grades, see the commercial casework guide.

What is millwork?

Millwork is the broad term for woodwork produced in a mill or shop rather than built entirely on site. It includes standing and running trim (casing, base, crown, chair rail), wall paneling and wainscoting, door and window frames, stair parts, columns, ornamental work and one-off pieces such as reception desks, nurse station transaction tops and feature walls.

In everyday commercial use, "millwork" often means the custom, non-repetitive architectural woodwork on a job, while "casework" means the cabinets. In residential use, "millwork" usually means trim and interior doors supplied by a lumberyard or millwork house. The what is millwork guide covers types, materials and pricing in detail.

Comparison table

CaseworkMillwork
Basic definitionCabinets and box-built storageShop-made architectural woodwork of all kinds
Typical itemsBase, wall and tall cabinets, open shelving units, lockers, lab cabinetsTrim, paneling, wainscoting, door frames, stair parts, reception desks, feature walls
RepetitionHigh: many units of a few typesLow: often one-off or custom profiles
Common spec sections06 41 00, 12 32 00, 12 35 5306 20 00, 06 40 00 and its subsections
Typical materialsParticleboard or MDF cores, HPL, TFL, edgebanding, wood veneerSolid wood, MDF, veneered panels, sometimes PVC or polyurethane
How it's countedBy cabinet, by linear foot, by typeBy linear foot, square foot, or each, depending on item
Main cost driversBox count, hardware, finish, countertopsProfile complexity, species, finish, site fitting
InstallSet, level, scribe, fasten to blockingFit, cope, scribe, attach, often more site labor per dollar

Where each appears in the specs (MasterFormat)

Most commercial projects organize specifications by CSI MasterFormat. These are the sections a cabinet or millwork estimator reads first:

  • 06 20 00 Finish Carpentry. Site-installed trim and simple woodwork, often handled by a carpentry sub rather than a woodwork shop.
  • 06 40 00 Architectural Woodwork. The umbrella section for shop-built architectural woodwork. Paneling, custom fixtures and other millwork usually land here or in its subsections.
  • 06 41 00 Architectural Wood Casework. Custom-built casework. The common subsections are 06 41 13 Wood-Veneer-Faced Architectural Cabinets and 06 41 16 Plastic-Laminate-Faced Architectural Cabinets.
  • 12 32 00 Manufactured Wood Casework. Casework from a manufacturer's standard product line, typically furnished by a casework manufacturer or dealer rather than custom-built.
  • 12 35 53 Laboratory Casework. Lab cabinets, fume hood bases and chemical-resistant tops, often with their own performance requirements.
  • 12 36 00 Countertops. Countertops specified on their own, separate from the cabinets underneath.

The practical takeaway: Division 06 is usually custom work built to the drawings, and Division 12 is usually manufactured product selected from a catalog. On the same school you might see classroom casework in 12 32 00, the library circulation desk in 06 40 00 and lab cabinets in 12 35 53. Each one can go to a different bidder. Read every section, not just the one with "casework" in the name, and check Division 01 for how the architect has split the work.

Who builds and installs each

Casework is built by custom architectural woodwork shops (Division 06) or by casework manufacturers (Division 12). Installation is often by the same company that built it, though manufacturers frequently sell through dealers who install, and some GCs set casework with their own carpenters.

Millwork is built by architectural woodwork shops and millwork houses. Simple trim may be supplied as stock profiles by a lumberyard and installed by a finish carpentry sub under 06 20 00. Custom millwork with special profiles, veneers or integrated lighting usually goes to an architectural woodwork shop that both fabricates and installs, because the fitting is where the risk is.

Three items commonly belong to someone else even when they touch your work:

  • In-wall blocking and backing, usually by the framing or rough carpentry sub
  • Plumbing and electrical connections at sinks, appliances and lit fixtures
  • Final painting of paint-grade millwork, if the spec assigns it to the painting section

Always confirm these against the spec and the bid form.

How casework and millwork are bid differently

Casework bids are count-driven. The estimator builds a takeoff of every cabinet by type, width and location, applies a unit cost or a build-up per box, adds hardware, countertops and install, and checks the total against cost per linear foot as a sanity check. Because units repeat, accuracy in the count matters more than anything else. Miss a 20-cabinet classroom type and the job is underwater. The cabinet takeoff guide walks through the count step by step.

Millwork bids are labor-driven. Trim gets measured by the linear foot per profile, paneling by the square foot or by elevation, and custom pieces like a reception desk are estimated as individual assemblies with their own material list and shop hours. The risk sits in profile complexity, joinery, finish and site fitting, so the estimator needs the sections and details as much as the plans.

A practical comparison:

  1. Quantity source. Casework: plans and elevations for count and widths. Millwork: elevations, sections and details for profiles and assemblies.
  2. Unit of measure. Casework: each cabinet, with a per-linear-foot check. Millwork: linear foot, square foot, or each.
  3. Labor split. Casework: mostly shop labor, with install roughly predictable per box. Millwork: more site labor per dollar, harder to predict.
  4. Common misses. Casework: cabinet types only shown on elevations, filler and end panels, countertops in a different section. Millwork: profile changes between rooms, returns and mitres, finish requirements buried in the spec.

Whichever you bid, the price should come from your own costs. The how to price custom cabinets guide covers building rates from your shop's real numbers.

Examples by building type

Building typeTypical caseworkTypical millwork
K-12 schoolsClassroom storage walls, teacher wardrobes, sink bases, art room and science cabinetsLibrary desks, wall paneling in commons areas, trim
HealthcareNurse station cabinets, exam room cabinets, med rooms, clean and soiled utilityNurse station transaction tops and fronts, wall protection paneling, reception desks
LaboratoriesLab base and wall cabinets, fume hood bases, reagent shelvingLimited: lobby or office areas
OfficesBreak room and copy room cabinets, storage wallsReception desks, feature walls, conference room paneling, executive office woodwork
ResidentialKitchen, bath, laundry and closet cabinetsBase, casing, crown, wainscoting, stair parts, interior doors, built-ins

Healthcare and lab work deserve a note: the spec often adds requirements for cleanability, chemical-resistant surfaces, specific hardware or third-party standards. Read those sections before you price, because they change materials and labor.

The gray areas

Some items don't fit cleanly. Here is how they usually fall, and why you should check rather than assume.

Countertops

Countertops sit on casework but are often specified elsewhere. Plastic laminate tops are usually in the casework section. Solid surface, quartz and epoxy resin tops may be in 12 36 00 Countertops, the lab casework section, or a separate stone section, and may go to a different trade. Your takeoff should list tops separately either way, so you can include or exclude them cleanly.

Wall paneling

Paneling is millwork, but when it's built from the same laminate-faced panels as the casework and installed by the same crew, some architects specify it in the casework section. Wood-veneer paneling with matching requirements is almost always architectural woodwork in 06 40 00.

Built-ins

A window seat, a library bookcase wall or a built-in entertainment center is box construction, so it's casework by build method. But it's often custom, one-off, and detailed like millwork, and in residential work it's frequently priced as millwork. Bid it the way it's built: if it's boxes, count boxes.

Reception desks and nurse stations

These combine casework (the storage boxes behind the counter) and millwork (the front panels, transaction tops and trim). Break them into both when you estimate so you don't underprice the custom parts at a box rate.

Getting the scope right

Before you price, run the drawings against the specs and write down which items you're including. A clear inclusions and exclusions list protects you when the GC levels bids, and the cabinet estimate template has a ready-made structure for it.

On large casework packages the count is the slow part. CabinetHub can take that step off your plate: you upload the plan set and receive an estimator-reviewed takeoff listing every cabinet with its type, size, room and sheet reference, which you then review, price with your own rates and send as your bid.

Frequently asked questions

Is casework the same as millwork?

No, though they overlap. Casework is cabinetry and box-built storage. Millwork is the broader category of shop-made architectural woodwork, which can include casework but also covers trim, paneling, frames and custom fixtures. On commercial projects the two are often specified and bid separately.

What is casework in construction?

Casework is the cabinetry on a project: base, wall and tall cabinets, shelving units and similar storage, built as boxes with doors, drawers or shelves. It appears in Division 06 when custom-built and in Division 12 when it's a manufacturer's standard product.

What CSI division is casework in?

Both. Custom architectural casework is in Division 06, typically 06 41 00 with subsections 06 41 13 (wood veneer) and 06 41 16 (plastic laminate). Manufactured casework is in Division 12, typically 12 32 00, with lab casework in 12 35 53.

Are countertops casework or millwork?

It depends on the spec. Laminate tops are usually included with the casework. Solid surface, quartz and resin tops are often in 12 36 00 Countertops or another section and may be bid by a different trade. Check the spec and the bid form before including them.

Who installs casework on a commercial job?

Usually the company that furnished it: the architectural woodwork shop for Division 06 casework, or the manufacturer or its dealer for Division 12. Some GCs install with their own carpenters. Blocking in the walls is typically by the framing or rough carpentry trade, not the casework installer.

Get your next takeoff done for you

Upload a plan set and get an estimator-reviewed cabinet takeoff: every cabinet with its type, size, room and sheet reference, traceable to the drawing. Price it with your own rates and send the bid from CabinetHub.

First takeoff: pay only if you're satisfied.

Start my first takeoff