Standard Cabinet Sizes and Dimensions Chart
In this guide
- Standard cabinet sizes at a glance
- Base cabinet sizes
- Wall cabinet sizes
- Tall cabinet sizes and pantry cabinet sizes
- Vanity cabinet sizes
- Sink base cabinets
- Corner cabinet sizes
- Fillers, panels and scribes
- Clearances that drive cabinet dimensions
- ADA and accessible cabinet dimensions
- Commercial casework follows different rules
- Using standard sizes in a takeoff
- Frequently asked questions
Standard cabinet sizes are the stock dimensions most residential cabinet lines are built to. A base cabinet box is 34-1/2" high and 24" deep, which gives a 36" counter height once a 1-1/2" top goes on. Wall cabinets are 12" deep and come in heights from 12" to 42". Widths for both usually run in 3" steps.
This page puts the numbers estimators, designers and installers reach for in one place: base, wall, tall, pantry and vanity cabinet dimensions, corner and sink base sizes, fillers and the clearances that drive the layout. Treat it as a reference for what to expect, not a substitute for the drawings. Every manufacturer has its own catalog, and a custom shop can build any size the job needs.
Standard cabinet sizes at a glance
The kitchen cabinet sizes chart below covers the headline numbers.
| Cabinet type | Height | Depth | Width range |
|---|---|---|---|
| Base cabinet | 34-1/2" box (36" with top) | 24" box | 9" to 48" |
| Wall (upper) cabinet | 12" to 42" | 12" (some 13" to 15") | 9" to 48" |
| Refrigerator wall cabinet | 12" to 24" | 24" | 30" to 36" |
| Tall / pantry / utility | 84", 90" or 96" | 12" or 24" | 18" to 36" |
| Oven cabinet | 84", 90" or 96" | about 24" | 27" to 33" |
| Bathroom vanity | about 30" to 36" finished | 21" (18" shallow) | 12" to 72" |
Base cabinet sizes
Base cabinets sit on the floor and carry the countertop. Nearly every other kitchen cabinet dimension on the elevation is measured from the top of the base run.
Base cabinet height
The standard box is 34-1/2" from floor to the top of the cabinet, including the toe kick. Add a 1-1/2" countertop and you land at 36" finished counter height. Stone tops are often 1-1/4" (3 cm) or 3/4" (2 cm) thick on a buildup, so check how the top is specified before you assume the box height is fixed. Some installers shim or use adjustable legs to hit 36" on an out-of-level floor.
Standard base cabinet depth
The standard base cabinet depth is 24" for the box, measured from the back of the cabinet to the face of the frame or the front edge of the box. Doors and drawer fronts add roughly 3/4". The countertop is usually about 25" to 25-1/2" deep so it overhangs the door faces by around an inch. Shallow bases (12" to 21" deep) exist for tight runs and furniture-style pieces, but they are a special order in most stock lines.
Toe kick dimensions
The toe kick is the recess at the bottom of the base that lets you stand close to the counter. It is typically about 4" high (some lines run 4-1/2") and about 3" deep. On frameless work it is often a separate base or leveler system with a loose toe kick board applied after install.
Base cabinet widths
| Base type | Common widths | Notes |
|---|---|---|
| Single door base | 9" to 21" | Narrow 9" units are often trays or spice pull-outs |
| Double door base | 24" to 48" | Some lines use a single door at 24" |
| Drawer base (3 or 4 drawer) | 12" to 36" | 15", 18", 21", 24" and 30" are the workhorses |
| Sink base | 24" to 48" | 30", 33" and 36" are most common |
| Trash pull-out base | 15" to 21" | Width depends on single or double bin |
| Microwave drawer base | 24" or 30" | Match the appliance spec sheet |
A dishwasher opening is 24" wide in a standard kitchen, and 18" for compact units. Ranges are most often 30" wide, with 36" and 48" pro ranges common in higher-end work. These openings are not cabinets, but they consume wall length and have to be counted in the run.
Wall cabinet sizes
Wall cabinets, also called upper cabinets, hang on the wall above the countertop. Wall cabinet sizes vary more than base sizes because the height has to work with the ceiling, the soffit and the backsplash.
Wall cabinet depth
Standard wall cabinet depth is 12" for the box. Some lines offer 13", 14" or 15" deep boxes so dinner plates fit more easily. Over the refrigerator, the wall cabinet is usually 24" deep so it lines up with the front of a standard-depth fridge enclosure or tall panels.
Standard upper cabinet height
Upper cabinet heights come in a predictable set. The standard upper cabinet height for an 8' ceiling is 30", with 36" and 42" uppers used for 9' ceilings or to run to the ceiling.
| Wall cabinet height | Typical use |
|---|---|
| 12" | Over refrigerator, over range hood |
| 15" | Over refrigerator, over range, stacked top row |
| 18" | Over range or microwave, stacked top row |
| 24" | Over refrigerator (24" deep), over sink with window above |
| 30" | Standard upper on an 8' ceiling with a soffit or open space |
| 36" | 8' ceiling run tight to the ceiling with crown, or 9' ceiling |
| 42" | 9' ceiling run to the ceiling or near it |
How upper cabinet height fits the ceiling
The common layout puts the bottom of the wall cabinets 18" above the countertop. With a 36" counter, that is 54" above the finished floor. From there the math is simple:
| Ceiling | Bottom of upper | Upper height | Top of upper | Space left above |
|---|---|---|---|---|
| 8' (96") | 54" | 30" | 84" | 12" for soffit, crown or open |
| 8' (96") | 54" | 36" | 90" | 6" for crown or a short soffit |
| 8' (96") | 54" | 42" | 96" | none, uppers to ceiling |
| 9' (108") | 54" | 42" | 96" | 12" for crown or stacked uppers |
Many designers drop to 15" between counter and uppers on small kitchens or raise it to 20" or more under tall appliances and coffee stations. The drawings govern.
Wall cabinet widths
Single-door wall cabinets usually run 9" to 21" wide, double-door wall cabinets 24" to 36", and some lines go to 42" and 48". Over-range and over-microwave cabinets are commonly 30" wide to match the appliance. Refrigerator wall cabinets are usually 30", 33" or 36" wide to match the fridge opening.
Tall cabinet sizes and pantry cabinet sizes
Tall cabinets run from the floor to the height of the wall cabinets or higher. The category covers pantry, utility, broom and oven cabinets.
Tall, pantry and utility cabinets
| Dimension | Common sizes | Notes |
|---|---|---|
| Height | 84", 90", 96" | 84" tops out at the top of 30" uppers; 96" reaches an 8' ceiling |
| Depth | 12" or 24" | 24" deep is the standard pantry; 12" is used where a full-depth unit would block a walkway |
| Width | 18", 24", 30", 33", 36" | 18" and 24" are the most common pantry widths |
Pantry cabinet sizes are usually picked to match the top line of the wall cabinets, so an 84" pantry sits next to a 30" upper that tops out at 84". Tall units are also used as refrigerator side panels and broom closets. Roll-out shelves and pull-out pantry hardware often have a minimum interior width, so check the hardware spec before you size a narrow pantry.
Oven and microwave tall cabinets
Oven cabinets are tall cabinets with an opening cut for a wall oven, a double oven, or an oven-and-microwave combination. They are commonly 27", 30" or 33" wide and about 24" deep, with the opening size taken from the appliance cut-out sheet. Never size the opening from a generic chart. Oven cut-out dimensions vary by brand and model, and a wrong opening is an expensive remake.
Vanity cabinet sizes
Bathroom vanities are shallower and, traditionally, lower than kitchen bases.
| Dimension | Standard | Notes |
|---|---|---|
| Depth | 21" | Some lines use 22"; 18" deep shallow vanities for small baths |
| Height (standard) | about 30" to 32" finished | Older and children's baths |
| Height (comfort) | about 34" to 36" finished | Now common in new construction and remodels |
| Width (single sink) | 24", 30", 36", 42", 48" | 12" to 21" units used as drawer banks |
| Width (double sink) | 60" to 72" | Often built from two sink bases and a drawer bank |
Vanity sink bases are usually 24", 30" or 36" wide. Vessel sinks and undermount sinks change the finished height you are aiming for, so check the plumbing fixture spec when the elevation gives a rim height rather than a counter height.
Sink base cabinets
A sink base has a false front at the top instead of a drawer, and usually no full shelf so the plumbing fits. Size it from the sink, not the other way around.
- A 30" single bowl sink usually goes in a 33" or 36" sink base.
- A 33" double bowl sink usually goes in a 36" sink base.
- Farmhouse (apron front) sinks need a dedicated apron sink base sized to the sink; check the sink's cabinet requirement.
- Undermount sinks need enough room between the cabinet sides for the bowl plus clips. The sink spec sheet lists a minimum cabinet width.
Corner cabinet sizes
Corners are where layouts go wrong. There are three common solutions, and each one consumes a different amount of wall.
Blind corner base cabinets
A blind corner base has a door on one side and a dead (blind) section that tucks behind the adjoining run. Common sizes are 36", 39", 42" and 48" wide. Many are adjustable: the cabinet can be pulled out from the wall a few inches to fit the run. A filler is almost always needed where the two runs meet so doors and drawers clear the handles on the adjoining cabinet.
Lazy susan corner base
A lazy susan base turns the corner with a rotating shelf system. Most catalogs size them by the wall space each leg occupies, typically 33" or 36" on each wall (LS33, LS36). They come with either a pie-cut (bi-fold) door or a diagonal front. The diagonal front version needs more wall on each side for the same shelf diameter, so read the catalog's wall requirement, not just the nominal size.
Corner wall cabinets
Diagonal corner wall cabinets are commonly 24" on each wall and match the height of the adjoining uppers. Blind corner wall cabinets are usually 24" to 36" wide and, like the base version, need a filler at the corner.
Fillers, panels and scribes
Fillers and panels are easy to miss in a count, but they are on every real job.
| Part | Typical size | Where it goes |
|---|---|---|
| Base filler | 3" or 6" wide, cut to fit | Between cabinets, at walls and at corners |
| Wall filler | 3" or 6" wide, height of the uppers | Same, for upper runs |
| Tall filler | 3" or 6" wide, height of the tall cabinet | Beside pantries and refrigerator panels |
| End panel | Cabinet depth by height | Exposed cabinet ends, dishwasher ends, island ends |
| Refrigerator panel | About 24" to 25-1/2" deep by tall height | Each side of a built-in-look fridge |
| Scribe molding | Thin strip, cut to length | Covers gaps between cabinets and out-of-plumb walls |
A good rule: leave at least a small filler at every wall so the cabinet can be scribed and the doors can open past the wall or casing. Corners almost always need one, because hardware and door swings collide otherwise.
Clearances that drive cabinet dimensions
These clearances do not come from the cabinet catalog. They come from appliance instructions, the designer and code.
- Countertop to wall cabinet: 18" is common. Many designs use 15" to 20".
- Range to hood or cabinet above: Follow the range and hood installation instructions. 30" from cooktop to the bottom of the cabinet or hood is a common figure, but the appliance manual governs.
- Over the refrigerator: Leave the gap the fridge manufacturer calls for at the top and sides for ventilation and door swing.
ADA and accessible cabinet dimensions
Accessible kitchens and baths change the numbers. Accessible counters and lavatories are typically lower than 36", knee clearance is needed under sinks and work surfaces, and reach ranges limit how useful a high upper shelf is. Do not rely on a chart for this. Check the 2010 ADA Standards for Accessible Design and the local code your project is permitted under, and build to what the architect shows on the accessible elevations.
Commercial casework follows different rules
Everything above describes residential stock cabinet conventions. Commercial casework works differently. Plastic laminate casework, institutional cabinets and lab casework are detailed by the architect and built to the AWI/AWMAC/WI Architectural Woodwork Standards at the Economy, Custom or Premium grade the spec calls for. Heights, depths and construction are set by the drawings and Division 06 or Division 12 specification sections, not by a catalog.
Using standard sizes in a takeoff
When you do a cabinet takeoff, standard sizes help you spot drawing errors fast. A wall run that does not add up in 3" increments, a 27" deep base nobody explained, or uppers that would hit the ceiling are all reasons to stop and check. If the drawings use catalog codes, our cabinet abbreviations guide explains how to read them, and how to read construction drawings covers finding the elevations and schedules where these dimensions live.
CabinetHub returns an estimator-reviewed takeoff that lists every cabinet with its type, size, room and sheet reference, so you can check each size against the drawing it came from before you price it.
Frequently asked questions
What is the standard size of a base cabinet?
A standard base cabinet is 34-1/2" high and 24" deep at the box, which gives a 36" finished counter height with a 1-1/2" countertop. Widths run from 9" to 48", usually in 3" increments.
How deep are standard upper cabinets?
Standard upper (wall) cabinets are 12" deep. Some manufacturers offer 13" to 15" deep uppers, and the cabinet over a refrigerator is usually 24" deep to line up with the fridge enclosure.
What height should upper cabinets be?
On an 8' ceiling, 30" uppers mounted 18" above a 36" counter top out at 84", while 42" uppers reach the ceiling. On a 9' ceiling, 42" uppers are common. The final height depends on the ceiling, crown and soffit.
How tall is a standard pantry cabinet?
Pantry and tall cabinets are usually 84", 90" or 96" high, 12" or 24" deep, and 18" to 36" wide. Most designers match the top of the pantry to the top of the wall cabinets.
What is the standard depth of a bathroom vanity?
Most vanities are 21" deep, with 18" deep shallow units for small bathrooms. Standard vanity height is about 30" to 32", and comfort-height vanities are about 34" to 36".
Are commercial cabinets the same size as residential cabinets?
Not necessarily. Commercial casework is built to the architect's drawings and the AWI/AWMAC/WI Architectural Woodwork Standards rather than a stock catalog. Always build to the drawings and field-verified dimensions.