Skip to content
CabinetHub

Cabinet Abbreviations and Codes on Drawings

Updated · 9 min read

In this guide
  1. How cabinet abbreviations and codes are built
  2. Cabinet type codes
  3. Accessory, filler and molding codes
  4. Architectural and blueprint abbreviations for cabinet scope
  5. Cabinet symbols on plans and elevations
  6. Always check the abbreviation legend
  7. Using cabinet codes in your takeoff
  8. Frequently asked questions

Cabinet abbreviations are the short codes that designers, architects and cabinet manufacturers use to label cabinets and parts on plans, elevations and order lists. A code like W3030 packs the cabinet type and its size into a few characters: a wall cabinet, 30" wide by 30" high. Learn the pattern once and you can read most kitchen drawings at a glance.

The catch is that nobody owns this cabinet nomenclature. Stock cabinet lines, custom shops and architects each use their own variations, and the same letters can mean different things on different sets. This guide covers the codes you will see most often, how size codes are built, the architectural abbreviations that matter for cabinet scope, and how cabinet symbols are drawn on plans. Use it as a decoder, then confirm against the legend on the drawings in front of you.

How cabinet abbreviations and codes are built

Most residential cabinet codes follow one pattern: a letter prefix for the cabinet type, then numbers for the size in inches, in the order width, height, depth. Depth is only written when it differs from the standard for that cabinet type.

CodeRead it asMeaning
B18Base, 18Base cabinet, 18" wide (standard 34-1/2" high, 24" deep)
DB24 or 3DB24Drawer base, 24Drawer base, 24" wide (3DB = three drawers)
SB36Sink base, 36Sink base, 36" wide
W3030Wall, 30, 30Wall cabinet, 30" wide by 30" high (standard 12" deep)
W1542Wall, 15, 42Wall cabinet, 15" wide by 42" high
W362424Wall, 36, 24, 24Wall cabinet, 36" wide by 24" high by 24" deep (over a refrigerator)
U188424Utility, 18, 84, 24Tall utility cabinet, 18" wide by 84" high by 24" deep
V3021Vanity, 30, 21Vanity, 30" wide by 21" deep (some lines write height instead)

Base cabinets usually show only the width, because the height and depth are standard. Wall cabinets show width and height. Tall cabinets often show all three. Suffixes such as L or R (hinge side), B or BUTT (butt doors, two doors with no center stile), or FH (full-height door) are common but vary by manufacturer.

Cabinet type codes

These are the kitchen cabinet abbreviations you will see most often on residential and light commercial drawings. The core letters (B, SB, DB, W, V) are close to universal; the longer prefixes differ from line to line, so treat them as likely readings, not rules. For dimensions behind each type, see our standard cabinet sizes chart.

Base cabinet codes

CodeCabinet
BBase cabinet (door and drawer)
SBSink base
DB, 3DB, 4DBDrawer base (number of drawers in front)
BBC or BCBlind base corner
LSLazy susan corner base
CB or CSBCorner base or corner sink base (varies by line)
BWB or WBBWastebasket / trash pull-out base
BPOBase pull-out (spice, tray or utensil)
BMW or MWBMicrowave base
FSB or ASBFarmhouse / apron sink base

Wall cabinet codes

CodeCabinet
WWall cabinet
WBC or BWCBlind wall corner
DC or WDCDiagonal corner wall
WMW or MWCWall microwave cabinet
WR or WSRWine rack or wall spice rack
GD or WGDGlass door wall cabinet (often a suffix instead)

Tall, oven and vanity codes

CodeCabinet
T, U or PTall, utility or pantry cabinet
OV or OOven cabinet (single, double or oven/microwave)
BR or BRMBroom cabinet
VVanity base
VSBVanity sink base
VDBVanity drawer base
VT or VLCVanity tower or linen cabinet

Accessory, filler and molding codes

Accessories are where takeoffs leak money. They rarely appear on a floor plan, but they show up on the elevations and in the order.

CodePart
BF3, BF6Base filler, 3" or 6" wide
WF330, WF342Wall filler, width then height (3" by 30" or 42")
TFTall filler
TKToe kick
CMCrown molding
LRLight rail (under-cabinet molding)
EPEnd panel
BEPBase end panel
WEPWall end panel
REPRefrigerator end panel
DWEP or DWPDishwasher end panel
SCScribe molding
OCM or OSCOutside corner molding
VALValance

Filler codes are the most inconsistent group. Some lines write BF3 and cut to width, others give full dimensions. Count every filler the elevation shows and note whether it is cut from stock or shipped to size.

Architectural and blueprint abbreviations for cabinet scope

On commercial sets and architect-drawn residential work, you will see standard architectural abbreviations instead of, or alongside, cabinet codes. These are the blueprint abbreviations that come up constantly in cabinet and casework scope.

Location and dimension abbreviations

AbbreviationMeaning
AFFAbove finished floor
TYPTypical (applies to all similar conditions)
SIMSimilar
NTSNot to scale
EQEqual (spaces divided equally)
CLRClear (clear dimension between finished faces)
OCOn center
CLCenterline
UNOUnless noted otherwise
VIFVerify in field
FVField verify
REFReference (or refrigerator, see below)

Materials abbreviations

AbbreviationMeaning
P-LAM or PLAMPlastic laminate
HPLHigh-pressure laminate
TFL or LPLThermally fused laminate / low-pressure laminate (melamine)
SS or SSMSolid surface material (SS can also mean stainless steel)
MDFMedium-density fiberboard
PBParticleboard
PLY or PLYWDPlywood
VNRVeneer
WDWood
GWBGypsum wallboard
CTCeramic tile (sometimes countertop)
BSBacksplash
BLKGBlocking

Scope and responsibility abbreviations

These matter most for pricing, because they tell you what is in your contract.

AbbreviationMeaning
NICNot in contract
BY OTHERSFurnished or installed by another trade
OFCIOwner furnished, contractor installed
CFCIContractor furnished, contractor installed
OFOIOwner furnished, owner installed
FF&EFurniture, fixtures and equipment (often a separate owner contract)
ADAAmericans with Disabilities Act (accessible station or clearance)

Appliance abbreviations

AbbreviationMeaning
REF or REFRRefrigerator
DWDishwasher
MWMicrowave
R or RNGRange
CT or CKTPCooktop
WO or OVWall oven
ICE or IMIce maker
UCRUndercounter refrigerator

Cabinet symbols on plans and elevations

Cabinet symbols are drawing conventions rather than codes, and they are fairly consistent across offices. Here is what you can usually rely on.

On the floor plan

A floor plan is a horizontal cut through the building, usually about 4' above the floor. Anything below the cut is drawn with solid lines, and anything above it is drawn with dashed (hidden) lines.

  • Base cabinets and countertops are drawn as solid lines, usually showing the countertop edge at about 25" from the wall.
  • Wall cabinets are drawn with dashed lines, since they sit above the cut plane, typically 12" from the wall.
  • Tall cabinets are drawn with solid lines at full depth. Some offices add an X or a diagonal across tall units or appliances to distinguish them, but this is not universal. Check the legend.
  • Appliances are usually labeled with abbreviations (REF, DW, R) rather than drawn in detail.
  • Elevation markers (a circle or arrow with a number and a sheet reference) point at each wall that has an interior elevation.

On the elevation

Interior elevations show the cabinets as you would see them standing in the room. They are where the real cabinet information lives.

  • Door swing is shown by two lines that start at the corners on the latch side and meet at a point on the hinge side. The point of the angle shows the hinge.
  • Drawers are drawn as horizontal rectangles, with drawer front heights often dimensioned.
  • Glass doors are often shown with diagonal hatch or a note.
  • Dimension strings give widths along the run and heights from the floor, often noted AFF.
  • Callouts reference sections and details on other sheets.

For a full walkthrough of how plans, elevations and details fit together, read how to read construction drawings.

Always check the abbreviation legend

Every competent drawing set has an abbreviation list and a symbol legend, usually on the cover sheet or the first G-series sheet (G001, G002 and so on). Interiors sets sometimes have their own on the first I-sheet. Read it before you start counting. It tells you how this particular architect writes plastic laminate, what they call a tall cabinet, and whether SS means solid surface or stainless steel on this job.

If a code appears that is not in the legend and you cannot resolve it from context, write it down as a question. Before bid day, send it as an RFI or note it as a clarification in your proposal. Guessing on nomenclature is how a shop ends up pricing laminate when the architect meant veneer.

Using cabinet codes in your takeoff

When the drawings already label cabinets with codes, your cabinet takeoff is partly done for you: you can count codes room by room. When they do not, which is common on commercial sets where the architect draws casework without catalog codes, you assign your own. Pick one consistent naming scheme for your shop and use it everywhere, from takeoff to shop drawings to cut lists.

CabinetHub takeoffs list every cabinet with its type, size, room and sheet reference, so each code on your list traces back to the sheet it came from.

Frequently asked questions

What does W3030 mean on a cabinet drawing?

W3030 is a wall cabinet 30" wide by 30" high. The W is the cabinet type, the first two digits are the width in inches and the next two are the height. Standard wall cabinet depth (12") is assumed unless a third number is added.

What does B18 mean for cabinets?

B18 is a base cabinet 18" wide. Base cabinets are standard height and depth (about 34-1/2" high and 24" deep), so only the width is written in the code.

What is the difference between SB and DB cabinets?

SB is a sink base, which has a false front at the top and open space for plumbing. DB is a drawer base, a base cabinet with a stack of drawers. A 3DB or 4DB code tells you the number of drawers.

What do AFF, TYP and NIC mean on blueprints?

AFF means above finished floor and is used for heights. TYP means typical, so the note or dimension applies to every similar condition. NIC means not in contract, so that item is not part of your scope.

Are cabinet abbreviations the same for every manufacturer?

No. The basic pattern of type letters followed by width and height is widely used, but prefixes, suffixes and filler codes vary between manufacturers and architects. Always confirm codes against the drawing legend and the manufacturer's catalog.

Get your next takeoff done for you

Upload a plan set and get an estimator-reviewed cabinet takeoff: every cabinet with its type, size, room and sheet reference, traceable to the drawing. Price it with your own rates and send the bid from CabinetHub.

First takeoff: pay only if you're satisfied.

Start my first takeoff